On Output Laser Phototypesetting

On Output Laser Phototypesetting

        The operator of the laser Imagesetter can open the file in the local software to help check the loss or obvious error of the file and correct the error. Therefore, this inspection method is very careful and stable, but it will waste a lot of time. Moreover, there are some defects in this method, which can not be found in the inspection; On Output Laser Phototypesetting

       This method is not available for postscript files. Although many production centers do this, it is also difficult to ensure that all required fonts exist in the workstation or rip, especially for the placed EPS files. The application file can tell us what font is used in the document, but it will not tell us what font is used in the EPS file.On Output Laser Phototypesetting

On Output Laser Phototypesetting

       Now there is software for pre inspection before output, which can help operators overcome these problems. These program checking software check PS files and allow us to view rasterized pages on the screen.On Output Laser Phototypesetting

Output the file to the laser Imagesetter

      In order to reduce costs, many output centers use common software and consumables. So the question is whether the materials used are reliable. If the result is reliable, it may be used. On Output Laser Phototypesetting

       For films wi s without brand, the quality of each purchase may be different. Therefore, a living piece looks good this month, but it may not be next month thout brand, the quality of each purchase may be different. Therefore, a living piece looks good this month, but it may not be next month. On Output Laser Phototypesetting

       If we use ordinary films and materials, we should always check the output results to calibrate our laser Imagesetter more often to ensure the stability of the quality of the final output. 

       In addition, the laser Imagesetter and developing equipment shall be cleaned frequently, and the liquid medicine for development shall be updated. In addition, keep close contact with the manufacturer or seller of laser Phototypesetter to maintain the correct working environment of the equipment.On Output Laser Phototypesetting

       Moreover, it is necessary to ensure that the laser Phototypesetter and developing equipment are handled in an absolutely normal and good working state. There are some problems with these equipment, which may cause waste and reduce efficiency. On Output Laser Phototypesetting

       Moreover, from the perspective of optimizing the operation of Phototypesetter, periodic calibration of equipment is a very key problem. On Output Laser Phototypesetting

       A good calibration status should ensure that our equipment produces the correct film density. Some output centers calibrate the equipment at the beginning of each cycle, which can be a day, a week or a month, and any time of material replacement.On Output Laser Phototypesetting

        We should calibrate the equipment with calibration test strips provided by the manufacturer or produced by third parties such as X-Rite and RIT. The test strip used should match our work.On Output Laser Phototypesetting

       Every time we add chemicals to the developing equipment or change chemicals and materials, we have to carry out testing. When changing from software to paper, it should also be tested.On Output Laser Phototypesetting

       If we use ordinary film, we should test each time we use a new roll of film until we can ensure that the quality of the film used each time is the same.On Output Laser PhototypesettingOn Output Laser Phototypesetting

Several ways to improve the efficiency of Phototypesetter

1. Sometimes, changing the direction of the Phototypesetting page can greatly improve the imaging speed. For example, for a page such as stationery, turning the long side to the axial direction during exposure imaging saves both exposure time and materials.On Output Laser Phototypesetting

2. If there is a group of live parts for output, remove the problematic live parts, image the smooth live parts first, then correct the problematic live parts, and then carry out the exposure imaging process.On Output Laser Phototypesetting

3. Ensure that there are enough films in the film box as far as possible, and take away the existing films in the film receiving box as far as possible. To reduce the loading and unloading time.On Output Laser Phototypesetting

4. For each document requiring film production, ask for a hard copy sample to compare whether the output effect is wrong.On Output Laser Phototypesetting

5. If some customers’ live parts often have problems when they are exported, and there is no money to make from these customers, they can be “dismissed”, but there is a problem in doing so, that is, such customers may run to their competitors.On Output Laser Phototypesetting

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)
Chat with us
Chat with us
Questions, doubts, issues? We're here to help you!
We are Cnpaperdoilies. Please leave your inquiry and your phone. We will give you feedback within 12 hours.
Our operators are busy. Please try again later
Have you got question? Write to us! Please leave your phone or what'sApp
This chat session has ended
Was this conversation useful? Vote this chat session.
Good Bad